CrispyDesigns
Active member
I’m similar weight and on the same set up as you. I’m at 205 psi and it’s spot on.
Have you equalised the negative chamber when pressuring the shock?
2024 Strive:ON
- Thread starter Rob Rides EMTB
- Start date
Have you equalised the negative chamber when pressuring the shock?
CrispyDesigns
Active member
“The Shit Flap”.
Keep mud and rocks out of your suspension crack.
Laser cut from 3mm rubber. Held on with some 3M VHB double sided tape. Nice and soft but should be decent wearing too. I’ll be testing it out this week in Snowdonia
Lol, looks good. Does it adhere to both parts, or just one? I've also been wondering how to keep stuff out of here because my rear mudguard doesn't quite reach down that far.
CrispyDesigns
Active member
It just adheres to the section of the main frame. It’s ‘solid’ enough to stay in place throughout the suspension travel/movement. I did wonder about adhering it to both sides but though it’d just pull off on the side that had less adhesion
Markwright1983
Member
Yeah, approx every 20psi I cycle the shock through it’s travel to equalise. I’ve even removed all air and started from scratch to be on the safe side.
How much sag are you getting at 205psi?
Markwright1983
Member
Looks like it should work. If you’re selling them, then I’d take one.
CrispyDesigns
Active member
I’m getting 25% sag approximately
Yeah, definitely. Are you doing them in black?
CrispyDesigns
Active member
I’ll keep the thread up to date if they test well and I make them available.
@Rob Rides EMTB what’s the deal on the forum with selling and advertising?
CrispyDesigns
Active member
At the moment I can only get this mid-grey. But, if they test well I’ll try and source black rubber (I have to use rubber that’s stable and safe to use on a laser cutter).
- Thread starter
- #971
All good on this kind of scale of thing
CrispyDesigns
Active member
Bob23
Member
Hello everyone from Toggenburg
Here are some pictures of my Strive:0n (750Ah / size M).
I must say I am very impressed with the build quality. The paint was flawless, all the torques were correct - only the brake needed bleeding.
The bike is fantastic to ride - an incredible climber! It gives you a lot of confidence going downhill, so I have to be a bit careful not to ride beyond my ability. I'm still getting used to the Bosch engine, coming from the EP8.
With my weight of 61 kg, the X2 shock is very easy to adjust - I had to take out the volume spacers from the fork to make it fit for me.
I did a few small upgrades, such as: xt cassette, xtr chain, swissstop discs, 50mm rise, 12 degree back sweep, 760mm wide handlebars, more comfortable grips and the mudguards. I wrapped it all in 3M stone protection film. Since there is no Garmin integration from Bosch, I mounted my old iPhone 7 with quadlock mount that I had lying around - now I can track and navigate directly over the Bosch flow app. The phone holds great so far, even in rough terrain. But maybe it will come off again.
With the tool pouches, lights and bell, the clean look is lost a bit, but hey, it's very practical.
I'm really happy with the bike so far!
Have a good ride and stay healthy…
View attachment 124461
Here are some pictures of my Strive:0n (750Ah / size M).
I must say I am very impressed with the build quality. The paint was flawless, all the torques were correct - only the brake needed bleeding.
The bike is fantastic to ride - an incredible climber! It gives you a lot of confidence going downhill, so I have to be a bit careful not to ride beyond my ability. I'm still getting used to the Bosch engine, coming from the EP8.
With my weight of 61 kg, the X2 shock is very easy to adjust - I had to take out the volume spacers from the fork to make it fit for me.
I did a few small upgrades, such as: xt cassette, xtr chain, swissstop discs, 50mm rise, 12 degree back sweep, 760mm wide handlebars, more comfortable grips and the mudguards. I wrapped it all in 3M stone protection film. Since there is no Garmin integration from Bosch, I mounted my old iPhone 7 with quadlock mount that I had lying around - now I can track and navigate directly over the Bosch flow app. The phone holds great so far, even in rough terrain. But maybe it will come off again.
With the tool pouches, lights and bell, the clean look is lost a bit, but hey, it's very practical.
I'm really happy with the bike so far!
Have a good ride and stay healthy…
Last edited:
Winryn
Active member
Took the bike to Bike park wales yesterday and rode the climb rather than using the uplift. Only had a window of 10-14.30 but managed 6 runs and 30 miles of riding. Finished with 42% battery so really impressed as my mates giant cut out at the top of the final run. Ran first 4 climbs in eco, 5th in trail and final in emtb. Did all the descents in emtb mode.
Bike is at home at bike park wales, couldn’t fault it on any of the trail types. Only negative is the Bosch motor rattle tbh, quite annoying and something I don’t usually notice as I ride with headphones when alone.
Bike is at home at bike park wales, couldn’t fault it on any of the trail types. Only negative is the Bosch motor rattle tbh, quite annoying and something I don’t usually notice as I ride with headphones when alone.
CrispyDesigns
Active member
A couple of rides testing The Shit Flap and it’s a little trooper! Been riding on trails and natural in Snowdonia so lots of loamy mud, slate shards, rocky descents and slop. Done a great job of keeping the poop out. The rubber seems to have a hydrophobic quality so a lot of the slop and mud doesn’t seem to stick.
A couple more rides to test the 3M VHB tape holds up then all being well I’ll make a short run of them and make them available on my site.
Could you please let me know when they're ready as I'd like to get one from you? Thank you
Same!
I'm keen, put my name down for a shit flap.
Hi everyone, I have some question on strive:ON, if someone have information :
- how is it compared to moustache game bike?
- some one all ready put on kios 300 screen on canyon bike?
- and how is canyon after marker service on electric bike?
- last question what is the hight ground and motor?
Thanks so much
- how is it compared to moustache game bike?
- some one all ready put on kios 300 screen on canyon bike?
- and how is canyon after marker service on electric bike?
- last question what is the hight ground and motor?
Thanks so much
CrispyDesigns
Active member
For me the Kiox 300 is the one I’d have.
Why's that? Looking st the 500 it is kinda big, but outside of that I don't really know the differences.
CrispyDesigns
Active member
Mostly due to size. The 500 looks to be too big for me. I have a Garmin 830 and have gotten used to the size. I can see all the information offered very clearly so can’t see me wanting a BIG screen
Yeah, I get it. That's why I wanted the Purion 200, but it's a system controller rather than a display, so seemingly can't be used in conjunction with the top tube controller (Which seems bizarre, given that it basically replicates the buttons of our Bluetooth mini remote, but adds a small, useful screen).
wessobert3000
Member
For those interested in a Strive On Underdog.
I ordered one twice and both looked like the paint was flawed.
According to Canyon, however, this must be so because it is carbon structures that remain deliberately visible.
Personally, I would find completely black honestly more beautiful, but that is probably a matter of taste.
Here is the statement from Canyon:
"Hi Marc,
thank you for the chat with my colleagues from 01.09.2023.
Please excuse, the misunderstandings regarding your chosen frame color Stealth.
The visible irregularities in the paint of your bike are not due to poor workmanship or damage. On the contrary, the effect is intentional and makes each bike unique.
With a "Raw" surface finish, like that of our bikes in the color "Stealth", we use a transparent layer of paint. Through this transparent varnish, the carbon fiber remains visible. The structure of the carbon fiber is naturally irregular. Even our most expensive and highest quality bikes have such a carbon structure. When you run your fingertips over the pattern, you'll notice that it feels flawless.
For more information on carbon frame finishes, click here.
Hopefully you like the unique look of your Strive:ON as much as we do. In the unfortunate event that you don't, I'm linking you to our returns page here for completeness."
The canyon support, however, I must expressly praise at this point. Always friendly and helpful. Short waiting times for chat / phone. With mails it takes a little longer, but still within the framework ...
I ordered one twice and both looked like the paint was flawed.
According to Canyon, however, this must be so because it is carbon structures that remain deliberately visible.
Personally, I would find completely black honestly more beautiful, but that is probably a matter of taste.
Here is the statement from Canyon:
"Hi Marc,
thank you for the chat with my colleagues from 01.09.2023.
Please excuse, the misunderstandings regarding your chosen frame color Stealth.
The visible irregularities in the paint of your bike are not due to poor workmanship or damage. On the contrary, the effect is intentional and makes each bike unique.
With a "Raw" surface finish, like that of our bikes in the color "Stealth", we use a transparent layer of paint. Through this transparent varnish, the carbon fiber remains visible. The structure of the carbon fiber is naturally irregular. Even our most expensive and highest quality bikes have such a carbon structure. When you run your fingertips over the pattern, you'll notice that it feels flawless.
For more information on carbon frame finishes, click here.
Hopefully you like the unique look of your Strive:ON as much as we do. In the unfortunate event that you don't, I'm linking you to our returns page here for completeness."
The canyon support, however, I must expressly praise at this point. Always friendly and helpful. Short waiting times for chat / phone. With mails it takes a little longer, but still within the framework ...
CrispyDesigns
Active member
What a way to start the day! Snowdon up the Llanberis and back down the Rangers. 4035ft in 14 miles. The bike didn’t miss a beat. Great fun on the way down and a beast on the way up
CrispyDesigns
Active member
The Shit Flap is a little trooper. Holding up very well. It’s done a great job at keeping the poop, mud, loam, rocks, stones and other unwanted items out.
I’ll definitely be making a short run of them when I’m back.
EMTB Forums
Latest articles
-
Bosch-powered Merida is here – the eOne-Sixty SL and eOne-Eighty intro and test
Merida has used Bosch-motors for years, but not on the emtbs. The full...- Knut Nes
- 10 min read
- Views: 4K
- Reaction score: 5
- Comments: 9
-
Bosch ABS Pro and Trail Pro - an interview about the new ABS profiles
When testing the new Bosch Performance CX gen5, we were also introduced...- Knut Nes
- 2 min read
- Views: 6K
- Reaction score: 2
- Comments: 5