-
Warning!!
Riding a tuned or deristricted EMTB is not a trivial offence and can have serious legal consequences. Also, many manufacturers can detect the use of a tuning device or deristricting method and may decline a repair under warranty if it was modified from the intended original specification. Deristricting EMTB's can also add increased loads for motors and batteries. Riding above the local law limit may reclassify the bike as a low-powered bike, requiring insurance, registration and a number plate.
Be aware of your local country laws. Many laws prohibit use of modified EMTB's. It is your responsibility to check local laws. Ignoring it, has potential implications to trail access, and risk of prosecution in the event of an accident.
We advise members great caution. EMTB Forums accepts no liability for any content or advice given here.
STUnlocker (ex Shimano STEPS Unlocker) Android & Windows App for derestriction/market change and etc
- Thread starter vadII
- Start date
- Thread starter
- #782
Posted the new version to Google Play. Let me know when you check it
- Thread starter
- #785
It works for me. I do not understand what can cause the process to stuck at the 0 step.
Try again
- Thread starter
- #787
It's uploaded for iOS, but it takes 1-2 days to approve the new version by Apple...Can you upload an iOS version as well? I bought both some time ago
p.s. The new version (.108) was uploaded to Google Play also, may be it will work for you...
Recently had a wheel true - spoke tension - replaced cassette..... the WO11 appears?
Not realising the magnetic was offset l then turn on STU app for clues.... tapped on Circumference..... changing the selection then back to Custom.
As a result later reading on possible causes the misaligned magnet was to the cause WO11....
I realigned magnet.... All powered up which is pleasing... only now restricted back to the limit?
Would appreciate input, a way to be reconfigured please.
Thank you.
Thanks!
Not realising the magnetic was offset l then turn on STU app for clues.... tapped on Circumference..... changing the selection then back to Custom.
As a result later reading on possible causes the misaligned magnet was to the cause WO11....
I realigned magnet.... All powered up which is pleasing... only now restricted back to the limit?
Would appreciate input, a way to be reconfigured please.
Thank you.
Thanks!
- Thread starter
- #789
You have a physical/electrical problem with the speed sensor. It has nothing to do with the settings of your bike.
Thank you vadll validating a electrical problem a result of the speed sensor...... I will research for the replacement speed sensor to the reinstall.
Thanks again.
Last edited:
What app is this ?
- Thread starter
- #792
Look at the title of the topic
Thank you vadll, l thought to run over this situation once more before upgrading parts another sensor.
Set up bike on the stand repositioned the magnet.... Took it for a run and fortunately NO error code is displaying..... the motor engages throughout the chosen settings Eco - boost.... only restricting the factory settings country of origin.... checked again on the app "Circumference" displaying "700c." I thought it possible "Custom" be chosen?
Just working on establishing wether the speed sensor still shows to be at fault as the error code no longer appears.
Thank you vadll.
- Thread starter
- #795
Yes, you can select "custom" and change to any value from 1300 to 3000
YES!!!.... Application applied thank you mate!.... all systems go!.... Merry Christmas vadll!....
Hi KuRi I read you reported some bad vibrations after having modified original Rise power parameters. Can you tell me more about, problem still present? Do you think it’s to do with too much power allowed?
thank you
Hi! Yes, after some more testing, it is all battery related. There is too much drain from the motor when >350W. That's why Orbea limited boost setting to 350W.
When the battery is full, you can use 400W-450W without problems, but as you reach 50% or less you start noticing some vibrations.
I have set up the boost setting to 400W and can be used for the whole range of battery with only some slight vibrations when <20% battery.
Hope this helps!
When the battery is full, you can use 400W-450W without problems, but as you reach 50% or less you start noticing some vibrations.
I have set up the boost setting to 400W and can be used for the whole range of battery with only some slight vibrations when <20% battery.
Hope this helps!
gigabyte772
Member
So I just got an Orbea Rise H10 but i upgraded fw to latest 4.1.8 by accident. I have copied the 2 files to the android fw folder, I tried to remove all files and just keep these 2 files and also just copied them with all other files, but it will not give me option to downgrade the software FW, it just stays on update page with no option to downgrade. Suggestions?
The downgrade firmware normally have a file name larger than existing firmware. It is typically 5.0.2 on the file name but is actually 4.0.2 firmware and hence the system things it is upgrading not downgrading. You should typically delete all the files from the FW folder and replace only with the 2 files that you need to downgrade.
gigabyte772
Member
I tried that. It is not prompting to update firmware.
Did you update the ETUBE application to version 5.0.3. `There is a comment in the update that says "Improved the modification detection function for unauthorised tuning" I wondered when i saw that how they could do it in ETUBE instead of the motor firmware but it is possible they are now preventing downgrades of the firmware somehow.
This is only a guess.
This is only a guess.
I am not sure about downgrading but that could mean that it will detect if the motor output (in W) or torque has not the default values also...
Edited: Yes, it has been confirmed that you cannot downgrade (yet) with the latest e-tube app. You have to install an old version.
Edited: Yes, it has been confirmed that you cannot downgrade (yet) with the latest e-tube app. You have to install an old version.
Last edited:
gigabyte772
Member
Where can I get older version?
gigabyte772
Member
Do you think if we default the bike in st unlocker then use Shimano to downgrade?
- Thread starter
- #807
Show a screenshot where we can see files which you copied for downgrade
gigabyte772
Member
- Thread starter
- #809
This folder MUST have many other files. It looks like you delete all files before or you created that folder by yourself. Try to use recommended file browsing Apps and copy FW files using a phone
EMTB Forums
Latest articles
-
Introducing the Forestal e-Cygnus - a downcountry and XC emtb
The new Forestal e-Cygnus is a slightly unusual emtb. It comes in two... -
2025 M1 Sporttechnik EN 8.0 review
The M1 EN is one of four M1 models built on the same frame. Well, it’s...