temon10
Well-known member
More range because of less power i guess. And if battery status is never shown correct it makes it hard to trust what your display says
go home when it showing 40% left
Just enjoy the ride.
Bafang m510
- Thread starter Puschtrale
- Start date
go home when it showing 40% left
Just enjoy the ride.
Mirkoser
Member
Hi guys, with this 48v firmware my bike is working well. I received it from Chilli Chen and besst pro is working as well..
thaeber
Well-known member
This is the firmware I‘m running for more then 3 month now. You find it on GitHub for motor rev I as well.
I ordered 3 units from Chilli, very responsive and helpful. You can find her in FB Dengfu group.
What a sleek remote, may i know where to get it? Appreciate your direction. Cheers
Thanks Lanton, i suppose is plug n Play ?
Hi everybody, I am about to order a M510 from Chili but the whole discussion concerning rev.1 vs rev.2, or rev "E" vs Rev "I" is very confusing, if I am honest.
Chili was telling me that the rev"I" firmware would belong to a 43V M510, but my final goal is to have the following setup:
M510, operating with both 48V and 52V batteries and being able to use the BESST Pro...
What do I need to order? Is there any sticker on the motor telling me/Chili what to look for.
Thanks in advance for any help,
Martin
Chili was telling me that the rev"I" firmware would belong to a 43V M510, but my final goal is to have the following setup:
M510, operating with both 48V and 52V batteries and being able to use the BESST Pro...
What do I need to order? Is there any sticker on the motor telling me/Chili what to look for.
Thanks in advance for any help,
Martin
Dado
Active member
Wondering why. You will set it for
Mate, dont worry, if you buy M510 now, you will get on 99% new revision - so rev "i" (mentioning again, I just named it like this according second byte in firmware bin file).
You can use also 48V firmware version with 52V battery, but you will have % SOC wrong. And there was also issues with some 48V firmwares - if you charge 52V battery to full, some firmwares was refusing - solution not to charge to full 58.8 V - but thats pain.
Here is posted 52V version firmware, which works great, Rob attached this file. If I remember it was version 3.2
Mate, dont worry, if you buy M510 now, you will get on 99% new revision - so rev "i" (mentioning again, I just named it like this according second byte in firmware bin file).
You can use also 48V firmware version with 52V battery, but you will have % SOC wrong. And there was also issues with some 48V firmwares - if you charge 52V battery to full, some firmwares was refusing - solution not to charge to full 58.8 V - but thats pain.
Here is posted 52V version firmware, which works great, Rob attached this file. If I remember it was version 3.2
BootsDave
Active member
It just needs to work with the firmware that Chili has already supplied. It’s the “i” version.
Mirkoser
Member
I have tested both
Revision i
Version 3.1 with 48v battery and besst pro. Working fine
Version 3.2 with 52v battery and besst pro. Working fine
but I switched back to 48v because I see no advantage for a 52v battery on a light all mountain bike
Revision i
Version 3.1 with 48v battery and besst pro. Working fine
Version 3.2 with 52v battery and besst pro. Working fine
but I switched back to 48v because I see no advantage for a 52v battery on a light all mountain bike
So if you change the 'current' parameter via besst pro for each pas level does it sort of overwrite the initial setting of a particular firmware? I like the idea of having more tunability instead of just using a particular fw and hoping it will suit well for my needs...
Dado
Active member
Yes, thats the reason of Besst Pro. Just u set power levels like on other motors.
But, ask yourself. Do u need to fidle with it? You just set it up once and thats it.
Only what is needed to lower Pass 1.
Lets bet how long would take to release mob. app for this power levels. My guess: mid 2023
But, ask yourself. Do u need to fidle with it? You just set it up once and thats it.
Only what is needed to lower Pass 1.
Lets bet how long would take to release mob. app for this power levels. My guess: mid 2023
steven_from_belgium
Member
@Rob Rides EMTB
when are you going to post the video of the Cheeb v2.0?
I'm waiting for your review of the M510.
to everyone, if you are waiting too like this
when are you going to post the video of the Cheeb v2.0?
I'm waiting for your review of the M510.
to everyone, if you are waiting too like this
Hi lanton. i want to use BBS remotes that i have stored. Could you say me the function of the cables on this explosed remote. when you acting buttons, mode + and Mode - you have continuity between wich cable color ? can you identified on the printed circuit wich cable color is the common of each buttons ? thank you for your help
Dado
Active member
Patdam, buttons are shorting only to ground, so just measure original buttons, which pin is ground and which pin is shorted when u press button. Or find a scheme of buttons on internet.
geirnaert jo
New Member
hello, do you do this with the same hardware that you use for besstt, is the pro version soft or also other hardware ?
danks
The right advice. There is a common wire, you need to check each wire to the button and solder it.
Thank you te two for your great helpful.
Pyr0
E*POWAH Master
Not sure if anybody uploaded/shared it, but I put copies here:
BESST Pro for Windows V1.0.30Beta_22020805.exe
File on MEGA
BESST Pro for MAC V1.0.31Beta.dmg
File on MEGA
[Edit] The mega links are broken, grab the latest versions files direct from Bafang servers. Just right-click and save as:
Windows:
http://test.api.besst.bafang-service.com/client/v2/firmware/upgrade/item/list/besst_pro_windowx_64
Mac:
http://test.api.besst.bafang-service.com/client/v2/firmware/upgrade/item/list/besst_pro_macos
Last edited:
thaeber
Well-known member
Oh, MAC version? Is it possible to login without account / bypass?Not sure if anybody uploaded/shared it, but I put copies here:
BESST Pro for Windows V1.0.30Beta_22020805.exe
BESST Pro for MAC V1.0.31Beta.dmgFile on MEGA
mega.nz
File on MEGA
BootsDave
Active member
I downloaded both. The Mac version won’t install, says file is corrupt. The PC version installs ok and seems to have username and password already set, but it’s in Chinese and haven’t managed to get it into English!
thaeber
Well-known member
Highly appreciated mate!
thaeber
Well-known member
I did change to German via settings, just check the left side options. Anyhow the account/ password does not work.
SchadowMaster
Member
There is a new python script. Download it and BESST Pro will be fully functional.
However, the new feature in the Pro version is that the Firmware can be updated without a username and password.
Pyr0
E*POWAH Master
Perhaps the mac version was corrupted during download.
The direct links to the files from bafang are below. Just right click and save as.
I put them on Mega as the downloads were slow when i grabbed them, but they seem to be a bit quicker today.
Windows:
Mac:
The direct links to the files from bafang are below. Just right click and save as.
I put them on Mega as the downloads were slow when i grabbed them, but they seem to be a bit quicker today.
Windows:
Mac:
Puschtrale
Active member
- Thread starter
- #930
So no other new features beside that? Then it is better keeping the old Besst Software that works with the loginbypass, cause this for me works well.
EMTB Forums
Latest articles
-
Bosch-powered Merida is here – the eOne-Sixty SL and eOne-Eighty intro and test
Merida has used Bosch-motors for years, but not on the emtbs. The full...- Knut Nes
- 10 min read
- Views: 5K
- Reaction score: 5
- Comments: 9
-
Bosch ABS Pro and Trail Pro - an interview about the new ABS profiles
When testing the new Bosch Performance CX gen5, we were also introduced...- Knut Nes
- 2 min read
- Views: 6K
- Reaction score: 2
- Comments: 5