Bafang M500/M600 Tuning & The BESST Tool

temon10

Well-known member
Feb 8, 2022
675
562
Malang, Indonesia
A question about m500 firmware: what is the difference between the two 10A firmware(2015.5 VS 2050.6). The first one is stock and feels kind of sluggish.. How does the other one compare to it? Currently using 12A and I like the snappiness of it(comparing to 13a) but I would like level1 to be more power efficient - sometimes doing really long rides...

2050.6 ismore powerful and smooth. Last time i used M500 the best for me is 10A 2050.6, now i'm using M510.
 

temon10

Well-known member
Feb 8, 2022
675
562
Malang, Indonesia
Attaching M600 firmware 43V 25A - up to 1300W with 48V battery!!!

->Be careful it is overheating, when u hold full throttle for few mins.
->Throttle has 1s delay when u not pedalling (Bafang what are you doing there!? Was it a purpose? )
->At 20% it shut down and then when I power on motor again it was showing only 1%. (Could be either motor went hard cut off or my battery BMS triped - with no load I measured 39V ) - which is good, as you would drain battery till the end.

So Dado.... if I have M510 43v, and I can run with my 48V battery?
 

TeoElFeo

Member
Apr 13, 2022
185
62
Tallinn
So guys, what's your favourite m500 48v firmware for trail riding? I think I've liked the 12a best out of all due to a good power ramp up(gives power earlier). The only issue I find is that even in PAS1 It's consuming way too much power, especially if you're going over 25-30km/h. Went to try the 2050 which seems more economical but lacks the initial oomph... Any suggestions here?
 

patdam

Well-known member
Jan 17, 2019
902
601
france
So guys, what's your favourite m500 48v firmware for trail riding? I think I've liked the 12a best out of all due to a good power ramp up(gives power earlier). The only issue I find is that even in PAS1 It's consuming way too much power, especially if you're going over 25-30km/h. Went to try the 2050 which seems more economical but lacks the initial oomph... Any suggestions here?
i prefer the 12a for my long riding in mountain. perfect for me if i'm alone, a little bit to powerful in 1 (of 5) level if i ride with friends non AE. +- 60% consumed for +- 30km +- 1500 D+, mostly in level 1 and 2.
What you whould mean by "It's consuming way too much power, especially if you're going over 25-30km/h" ? you have over pass the 25 km/h limit (not me) ? in this case it is normal if you consume more, no ?
 

fantic.e-bike

New Member
Sep 24, 2022
4
0
Belgique
hello, my name is julien I have a FANTIC ISSMO 45km / h with engine bafang m600 configure with the counter bafang two modes of assisstance are available 'road' and 'hill', it is a valley they have completely bridle since it uses a battery 630w, I would like access to the engineer level in order to unlock the speed limit, can you explain me + in detail with python? Thank you
 

fantic.e-bike

New Member
Sep 24, 2022
4
0
Belgique
You can download the BESST Tool from there, you then need to contact them to obtain an ID/Password :


They can give you a basic password. But each ID/Password links to their system and has different abilities and can change different things.
hello, my name is julien I have a FANTIC ISSMO 45km / h with engine bafang m600 configure with the counter bafang two modes of assisstance are available 'road' and 'hill', it is a valley they have completely bridle since it uses a battery 630w, I would like access to the engineer level in order to unlock the speed limit, can you explain me + in detail with python? Thank you
 

mgx

Active member
Feb 18, 2021
110
112
Slovakia
I advise to stop repeating same question and go to this thread from page1. then read... you will find

Or check this, step by step


Script is here

 

vikino1

Active member
Oct 14, 2021
74
102
Slovakia Topoľčany
I'm asking for advice, I have a Besst tool, everything works fine for me, but I can't increase the speed but only decrease it. Is this caused by the Besst tool itself, or is it just a bug in the Python login?
 

Dado

Active member
Jun 28, 2022
692
463
Bratislava
Same with me with python script. Theres some region restriction and can set only 25kmh.

You can buy K1 CAN monitor:

IMG_20220926_174119.jpg
 

fantic.e-bike

New Member
Sep 24, 2022
4
0
Belgique
I advise to stop repeating same question and go to this thread from page1. then read... you will find

Or check this, step by step


Script is here

hello, thank you for your answer and sorry for the duplicate, however if I ask the question it is that one of the steps is failing me, I have never manipulated the codes, suddenly I followed the glass procedure nevertheless when I run the script, there are two lines of writing and .. nothing more and I enter any identifiers in BESST and nothing .. I installed simpleson etc via ms dos command, however, I am precisely independent in the electric but my dealer access limits me to 25km/h while I also sell 45km/h... so I need you guys please, you're the only ones working on it... help me please
 

fantic.e-bike

New Member
Sep 24, 2022
4
0
Belgique
My son started it according to this guide Bestt Python Methode Download the RAR in post No. 8.
hello, I come to the news, I finally succeeded in bypassing the login to find myself with the same functionalities as my classic accesses.. the pro script does not work? how to access the engineer version of the software? I use the official interface, does not work on version 1.2.16 .. how can I do? thank you
 

vikino1

Active member
Oct 14, 2021
74
102
Slovakia Topoľčany
I don't understand your post, probably because of Google Translate. I will connect to the display and the controller via Besst. I can't increase the speed but only decrease it. I can change the firmware. Besst worked for me from 2.1.18 up
 

Slaine

Member
Apr 12, 2022
97
39
France
Hi,

I would like to know why I can't read my paprameter with besst tool pro?
I have a error message
thanks for your help
Capture.PNG
 

Waynemarlow

E*POWAH Master
Dec 6, 2019
1,108
889
Bucks
Slaine, as far as I'm aware the M600 firmware is not useable with the BEEST Pro. Only the later revisions of the M510. If you wish to upgrade the Firmware then you will have to use only the original BEEST software.
 

Mida

Member
Oct 23, 2022
7
1
ČR
Hi, I just update my M500 36v with CRX10NC3615i142017.5-28-2230-20200519-2.bin (Leader Fox stock firmaware) and it is amazing!!
I'm gettting 850w peak. 20A.


I hope that I will not burn out the controller 🤞. But as it is stock firmware, should be OK!
Hi,
I also have an M500 engine and would like to flash the firmware to something more powerful.
I currently have CRX10NC3615i142055.8 firmware

Are you still using CRX10NC3615i142017.5-28-2230-20200519-2.bin firmware??
Is everything okay in the long run?
It is interesting that the power is around 18-20A, while the firmware marking is 15A?
 

krokan

Member
Oct 20, 2021
55
21
B
Hi,
I also have an M500 engine and would like to flash the firmware to something more powerful.
I currently have CRX10NC3615i142055.8 firmware

Are you still using CRX10NC3615i142017.5-28-2230-20200519-2.bin firmware??
Is everything okay in the long run?
It is interesting that the power is around 18-20A, while the firmware marking is 15A?
Yes. I'm still using it and it is great. More than 3000km without any problem.
 

EMTB Forums

Since 2018

The World's largest electric mountain bike community.

555K
Messages
28,072
Members
Join Our Community

Latest articles


Top