What did you buy your ebike this week?
- Thread starter Simoto123
- Start date
OldnSlow
Member
Ah yes, nuns. Who doesn't have fond memories of catechism and firmly struck knuckles with the edge of a wooden ruler by Sister Mary Euthanasia and Sister Veronica Eugenica
Chased by a dozen nun's what, exactly?
Is that the R version or the newest S? I have the R version on my SB130, been debating getting it upgraded to the S. I’d have to send it back to Push as my local Push dealer can’t do it so that would mean sending it back to the US, it ends up being expensive!
Lawyers?
Semmelrocc
E*POWAH Master
It's new helmet day today. TLD Flowline for some style and safety on the trail.
Some new rubber. I asked my LBS to order me a couple of Specialized Cannibal's since I have a gift voucher, and everyone is saying how good they are in wet gloopy conditions. I didn't hear from them for a few days... and then Tweeks sent me an email with 40% off Michelin tyres. I've had Enduro Wilds for my last few tyres, but thought I'd try the Racing Line Enduro Wild this time as it's apparently a bit softer / grippier.
The next day, my LBS confirmed my Cannibal's are ordered. Looks like I'm going to end up with 4 tyres!! I might just put the Wild's away until Spring!
The next day, my LBS confirmed my Cannibal's are ordered. Looks like I'm going to end up with 4 tyres!! I might just put the Wild's away until Spring!
Last edited:
Also new helmet day, a leatt gravity 4.0 to replace my old battered fox proframe.
Also got it for £138 on CRC a few days back before it crept back up
More padded than the fox, breathes well and non detachable chinguard as I don't like them.
Also got it for £138 on CRC a few days back before it crept back up
More padded than the fox, breathes well and non detachable chinguard as I don't like them.
The rest of some Fox 38's to go with this honorary leaning tower of pisa cut part of my steerer ...
I was in a hurry ... wanted to ride ... the bearing/bushing on the blade for the pipe cutter I started with had obviously collapsed - so I continued in a surgical manner with an angle grinder .. there's a lot to be said for using the proper tools
Don't worry ... inserting the star nut with a rubber hammer and a chainsaw screwdriver was no less pretty ...
For the weight weenies .. that cut saved 25g .. so the 170mm 29er 38's with axle weighed in at 2287g. Maybe 26g if I'd cut straight ...
I was in a hurry ... wanted to ride ... the bearing/bushing on the blade for the pipe cutter I started with had obviously collapsed - so I continued in a surgical manner with an angle grinder .. there's a lot to be said for using the proper tools
Don't worry ... inserting the star nut with a rubber hammer and a chainsaw screwdriver was no less pretty ...
For the weight weenies .. that cut saved 25g .. so the 170mm 29er 38's with axle weighed in at 2287g. Maybe 26g if I'd cut straight ...
Mcharza
E*POWAH BOSS
Well, it depends on you
It hasn't got much of a chance then...Well, it depends on you
New tire for rear, MaxxTerra instead of MaxxGrip.
Does Maxxis have quality issues or am I to sensitive? First tire received showed lack of rubber and partly eroded blocks. Overall surface did not look like used from other tires before. Replaced version was better but is tough to get on rim:
Does Maxxis have quality issues or am I to sensitive? First tire received showed lack of rubber and partly eroded blocks. Overall surface did not look like used from other tires before. Replaced version was better but is tough to get on rim:
steve_sordy
Wedding Crasher
My DMR Vaults were getting a bit clattery, so I bought some bushes and bearings from Rulla Bearings:
Pedal Bearing Kits Archives • Rulla Bike Bearings
But I got this minimalist kit from them via eBay for £8.50 delivered.:
They fit V11 and Vaults
Later addition: I already have the fitting tool which is simple and very good, but you only really need a bolt with the correct screw thread size and you can remove the bush by hand with it. The thread bites into the soft bush and gives enough purchase for you to pull out the bush. The bush has a chamfer at one end, make sure that the chamfer goes into the pedal. If you get it square, you can push it in by hand.
Pedal Bearing Kits Archives • Rulla Bike Bearings
But I got this minimalist kit from them via eBay for £8.50 delivered.:
Pardon our interruption...
www.ebay.co.uk
They fit V11 and Vaults
Later addition: I already have the fitting tool which is simple and very good, but you only really need a bolt with the correct screw thread size and you can remove the bush by hand with it. The thread bites into the soft bush and gives enough purchase for you to pull out the bush. The bush has a chamfer at one end, make sure that the chamfer goes into the pedal. If you get it square, you can push it in by hand.
Last edited:
Something to keep me busy at the end of the week...
The start of the bling begins!
2 x Carbon hoops ordered.
Just awaiting confirmation from my LBS if they're still a Hope dealer as I quite fancy their new cheese. I had i9's on the Heckler and loved them, I still might buy some again in the future depending on how this wheel build goes.
2 x Carbon hoops ordered.
Just awaiting confirmation from my LBS if they're still a Hope dealer as I quite fancy their new cheese. I had i9's on the Heckler and loved them, I still might buy some again in the future depending on how this wheel build goes.
Hey! I just got a set of those last week to replace my old Ergon winged-type grips.
Ergon Ga2
No more hand-cramping and a little better control. And I’m paying more attention to geometry which probably helps also.
Last edited:
Just bought ...
2 x Schwalbe Magic Mary Super Gravity Ultra Soft TL Black / 29" / 2.4" / Folding
... for £87 (43.50 each) from Merlin Cycles.
Normally £59 each but special offer is buy 2 for £87.
Needed tyres for both wife and my bikes, so result!
2 x Schwalbe Magic Mary Super Gravity Ultra Soft TL Black / 29" / 2.4" / Folding
... for £87 (43.50 each) from Merlin Cycles.
Normally £59 each but special offer is buy 2 for £87.
Needed tyres for both wife and my bikes, so result!
Last edited:
TankCommander
Member
Couple of weeks ago, riding my Levo Hardtail, I smashed my derailleur, bent it 180 degrees, caught in the back wheel breaking six spokes, twisted the chain and did some damage to the cassette. My local bike shop suggested I consider the Shimano Cues system as a replacement which also gave me the opportunity to change from 9 to 11 gears. Couldn't be happier, those couple of extra gears have made a big difference, notably, there is one track that even on turbo I had never been able to get up, I managed to do yesterday. Expensive? yep, Happy, you bet - feels like a new bike, and way cheaper!
Plummet
Flash Git
Changing out from shifty 12sp gx to 11 speed Shimano xt link glide
Ordered these thinking they were the brisker versionI was wrong just the waterproof gloves but I’ll give them a go now I have them, super tight hopefully better when broken in, anyone else tried them ?
View attachment 126804
Update .. rode with them today thought they were awful ! No dexterity in the glove and the insert seem to have sharp parts digging into my fingers… not impressed at all
UnreasonableMuppet
Well-known member
I want the link glide too, but I need a compatible free hub, so it's link glide + new wheel or new hub. So I have been sticking to the cheap and cheerful deore
Plummet
Flash Git
Yeah, I had to buy the hg freehub too. It's worth it though. I'm saving WAY more in the long run switching out from sram.
Zed.
Active member
bought a 'pre-loved' set of forks for my Rail5, I already have some of Manitou's Mezzer Expert forks on my NP Mega and rate them highly, a set of Mezzer pro forks were on ebay so a bid was placed & sucessfull
when they arrived I gave them a service and will hopefully find time to fit them this week
Rich.
when they arrived I gave them a service and will hopefully find time to fit them this week
Rich.
Amber Valley Guy
Active member
Just ordered a RS Yari RC to replace my 35 silver TK, my thoughts being I can easily upgrade the Yari if I need more.
Similar threads
EMTB Forums
Latest articles
-
The most reliable motor brand (in Norway)
A poll was posted on a big Norwegian emtb facebook group. There are...- Knut Nes
- 3 min read
- Views: 995
- Reaction score: 5
- Comments: 5
-
2025 Canyon Spectral:ONfly CF Ltd review
We were quite surprised to read about the new lightweight Canyon...- Knut Nes
- 7 min read
- Views: 929
- Comments: 1