TCFlowClyde
Active member
I doubt she knows honestly. Let's ask LC-Jim.
I have a BEEST too but not sure there's much tuning beyond factory settings.
Maybe in the near future, some programmers on this forum can modify the 820 firmware.
Bafang m820
- Thread starter Vsoria
- Start date
I have a BEEST too but not sure there's much tuning beyond factory settings.
Maybe in the near future, some programmers on this forum can modify the 820 firmware.
If you have not noticed Jim's postings in the LCE930 thread...
There are two separate versions of the m820 36v and 43v.
The Besst can be used on the m820.
There are two separate versions of the m820 36v and 43v.
The Besst can be used on the m820.
Found this on ebike-international
"
Boost Your Ride
Another great feature of the M820 is the boost function called “Rocky”. Activating this function is simple, with a single or double click on the “+” sign, dependent on if you already in the boost mode. When entering the “Rocky mode” (seen in the display as a special Rocky icon) the rider will enjoy a “Rocky push feeling” for a set continuous period."
"
Boost Your Ride
Another great feature of the M820 is the boost function called “Rocky”. Activating this function is simple, with a single or double click on the “+” sign, dependent on if you already in the boost mode. When entering the “Rocky mode” (seen in the display as a special Rocky icon) the rider will enjoy a “Rocky push feeling” for a set continuous period."
TCFlowClyde
Active member
Aka "Beast-mode".
So who made the frame Bafang used for their demo video?
TCFlowClyde
Active member
I wonder if the purported 75Nm max/95Nm peak will make a big power delivery difference between the 36 V and 43V. How to predict it? I assume that the difference will translate into delivering less peak Nm and W to 36V?
In comparison, my M600 43V delivers a little less power than my bigger M600 48 V. It's noticable but barely. And the 43V seems to delivery smoother shifting...
The voltage should have nothing to do with power. Power is power. 600w=43vx14a 600w=36vx16.6a
The only difference is that the lower voltage system requires heavier bigger copper wires to carry the increased amperage.
Again the shifting system probably runs off a low voltage and it is dropped down from either size battery so it should make no difference.
Now if you have systems that don't take into account the difference in amperage then indeed you might see loses. If the 36v system does not have bigger wires then you will have higher resistance in the paths and that will cause lower performance.
The only difference is that the lower voltage system requires heavier bigger copper wires to carry the increased amperage.
Again the shifting system probably runs off a low voltage and it is dropped down from either size battery so it should make no difference.
Now if you have systems that don't take into account the difference in amperage then indeed you might see loses. If the 36v system does not have bigger wires then you will have higher resistance in the paths and that will cause lower performance.
Last edited:
TCFlowClyde
Active member
Please provide your motor performance review and post ASAP!
This is good news. I am concerned about the question of how we will fasten the chain holder?
TCFlowClyde
Active member
Nice. So two pre-programmed tunes: one at 100% and the other at a gradual step up?Today I read out the data with BESST
View attachment 108232
View attachment 108235
View attachment 108234
No, the top graph is speed and the bottom graph is performance
Waynemarlow
E*POWAH Master
Run a Narrow Wide chain ring and you can throw it in the bin. I've now been running over 12 months on my M600 with a NW chain ring and never had a derail.
Who is the manufacturer of the NW star? Please give a link to NW. I have a Chinese WN front star. And the chain flies off my star.
RACEFACE, Wolftooth, Funn etc
I don't use a chain guard on any of my 1X bike, never had a chain jump off.
I don't use a chain guard on any of my 1X bike, never had a chain jump off.
TCFlowClyde
Active member
No chain guide needed. RF NW have on all 3 bikes. No chain drops on rough desert terrain Imin 5 yrs +.
Thanks! Which chain do you use?
I just use a SRAM XX1 because it is rated the longest life. No special ebike chain.
great news to see that it's fully compatible with BESST!
I had a question as it's my first badant build, do they provide the crankset with the motor ? If yes, how much does it weight ?
I'm trying to make a quick estimate on the total weight. I'm at 18.8kg so far, let's see how it goes
I had a question as it's my first badant build, do they provide the crankset with the motor ? If yes, how much does it weight ?
I'm trying to make a quick estimate on the total weight. I'm at 18.8kg so far, let's see how it goes
TCFlowClyde
Active member
Yes crank arms should be included within the motor kit. They did for both my M600s and M620. They are Bafang OEM and likely 170 mm in length. Lower to decent quality, but too long for many that will go shorter 155-160 mn to minimize pedal strikes that most emtbs are prone too...even lighter ones like the 820 builds ...just less from what I hear due to slightly lighter motor.
I doubt the stock Bafangs are lightweight. But they are listed as ISIS interface compatible, so lots of aftermarket crank arms that will be much lighter and higher quality are out there to purchase, both carbon and alloy. Which is awesome;
Just Google Bafang m500/600 crank arms and see if a weight is listed...I'm betting they'll be close to the m820 ones.
TCFlowClyde
Active member
Here's my E-Hope 155 mm cranks at 465 g. Not superlight but very strong, as I predict I will have to pedal more out of the saddle with the 820 like when I rode the TQ50/Fazua60/Shimano RS lower torque motors.Yes crank arms should be included within the motor kit. They did for both my M600s and M620. They are Bafang OEM and likely 170 mm in length. Lower to decent quality, but too long for many that will go shorter 155-160 mn to minimize pedal strikes that most emtbs are prone too...even lighter ones like the 820 builds ...just less from what I hear due to slightly lighter motor.
I doubt the stock Bafangs are lightweight. But they are listed as ISIS interface compatible, so lots of aftermarket crank arms that will be much lighter and higher quality are out there to purchase, both carbon and alloy. Which is awesome;
Just Google Bafang m500/600 crank arms and see if a weight is listed...I'm betting they'll be close to the m820 ones.
Nice, it’s not that heavy! I’ll try with the ones provided by default and I’ll see if it’s needed to upgrade
TCFlowClyde
Active member
Here's my stock Bafang M600 I70 mm (without heavy steel crank bolts 15-20 g) in comparison. 530-465 = 65 g
I'll likely shave off 100g going aftermarket alloy and shorter. Not a lot much higher but much stiffer crank arms and bonus; some bling looks.!
I'll likely shave off 100g going aftermarket alloy and shorter. Not a lot much higher but much stiffer crank arms and bonus; some bling looks.!
Last edited:
TCFlowClyde
Active member
I found alloy crank bolts and included them in. 580 g. So 580-465 = 115 g saved! A little better. (Damn alloy cranks bolts were heavier than I thought.
)
So new Bafang 170 arms.
)So new Bafang 170 arms.
The crankset that is inclusive with the motor kit weight 498 Gramm incl. bolts.
Last edited:
TCFlowClyde
Active member
Cur
Curious...what length?
Sorry 498 Gramm at 170mm lenghtCur
Curious...what length?
EMTB Forums
Latest articles
-
Santa Cruz Vala X0 review - a new approach to perfection?
The new Vala is Santa Cruz’ first attempt on a Bosch-powered emtb. Like...- Knut Nes
- 6 min read
- Views: 2K
- Reaction score: 5
- Comments: 8
-
A new standard for charging ebikes is coming? A quick interview with Bosch - charge2bike
I had a quick chat with dr Vikram Godbole about "charge2bike", a new...- Knut Nes
- 2 min read
- Views: 1K
- Reaction score: 7
- Comments: 5