temon10
Well-known member
only M510 FC 2.0 can change power level via BESST Pro
Bafang M500 and M600 motors
- Thread starter Rob Rides EMTB
- Start date
Dado
Active member
That is right, only when u have second revision of M600 controller. So you wont flash this firmware 46.2 into old M600. Why the hell is firmware number less then latest firmware into old M600?
And yes, it works with Besst Pro.
And yes, it works with Besst Pro.
Dado
Active member
Not true, now also new M600 and also M510 FC1.0
M510 FC2.0 has also advanced power level setup - Assistance level and acceleration (which now works) for every pass levels.
Would u like me to do screenshots?
Last edited:
have you pics of this power level change with BESST pro ?
I have last rev of BESST pro and i can adjust current limit percentage for each level, but not the power level ? currrent adjust is applicable on my M510 rev 1.0, not on M500 and 600.
Dado
Active member
By power level I mean Current Limit Percentage. Sorry. It is almost the same.
Here is M600:
Here is M600:
temon10
Well-known member
so u change parameter of m600 46.2 version with your blackbox or also can change with besst pro?
OK we speak of the same thing. For my part i can only modified seeting of the M510, i can't for my M600.
it's you seeting of the M600 ? impossible to apply that on my M510 ?
i have an question about about these current limits. Does somebody know exactely at wich current limi coresponding the 100% of each level ? In use, with original seeting (all at 100%), The max power level increased when you increase the level. I have tried 80% at level 1 and in fact that reduce a lot the power (too many). That whould mean that the 100% of the level1, is in fact already an reducion of the max power, of how many percent ?
Dado
Active member
Hello Temon
Yes, BB3 is sending same configuration packets, but without password needed.
You can set also in Besst Pro as you can see from my pictures. I just noticed this on my BB3 device, when I was testing it on different motors. And this M600 motor I bought like 4 months ago. I just let it stay in a box as I thougt it is just normal M600 with older firmware.
Finally possible to change max power on M600. And I guess next version of M600 will have controller from M510 FC2.0 - so even more setup parameters.
Last edited:
Dado
Active member
Sorry mate, been reading your post 3 times, but dont understand to your questions.
)100% current on pass 1 can give you full power on pass 1.
With M510 FC2.0 controller, where you have also support level percentage setting ( something like sensitivity to your pedalling, or how much torque should add motor to your legs torque. Can be set 0 to 500%) , it could work also with rediculously high current levels even on pass 1.
Reality - when it was on default 50% current on pass 1 - I have again not even pushing into peddals and was going fast as hell.
I am suspecting the torque sensor is not so sensitive.
Last edited:
sorry for my bad english (i"m also not more clear in my language sometimeSorry mate, been reading it 3 times, but dont understene to your questions.
100% current on pass 1 can give you full power on pass 1.
With FC2.0 controller, where you have also support level percentage ( something like sensitivity to your pedalling, or how much torque should add motor to your legs torque. Can be set 0 to 500%) setting, it could work also with rediculously high current levels even on pass 1.
Reality - when it was on default 50% current on pass 1 - I have again did not even pushing into peddals and was going fast as hell.
)I whould mean that full power (100%) on pass1 is not the same of pass5, that whould mean that the 100% of the pass1 is in reality allready less percentage than the full power (i'm clear ?). I asked if somebody know how many reducing percentage on each level would mean the 100%
About the sensibility of your settings. It's very different on my M510 rev 1.0 (i have replaced my torque sensor) ?
temon10
Well-known member
Just try it on 46.2 firmware and it can be tuned with Besst pro. thanks broHello Temon
Yes, BB3 is sending same configuration packets, but without password needed.
And this M600 motor I bought like 4 months ago. I just let it stay in a box as I thougt it is just normal M600 with older firmware.
Finally possible to change max power on M600. And I guess next version of M600 will have controller from M510 FC2.0 - so even more setup parameters.
Dado
Active member
Hmmm, that does not make sense to me.
Anyway, somebody knows if possible to buy M510 controller ? If so, where?
Anyway, somebody knows if possible to buy M510 controller ? If so, where?
Dado
Active member
temon10
Well-known member
sorry i got new controller with 46.2 firmware from factory. old controller is dead.
Dado
Active member
Same here, have it only in a controller. Sorry
Dado
Active member
Crazy Bafang. With firmware 46.3 or 46.4 power settings are failing in BESST Pro - and not possible to read.
Have 46.4 48V if somebody wants.
Have 46.4 48V if somebody wants.
temon10
Well-known member
Some source said that before M510 FC 2.0 the controller made by third parties factory and have lot problem. So weird that controller have to be the most quality control.
Please share only rev do you have tested and you are sure that able to download to your controller (mention your controller rev end your country location).
BAFANG have share with me several rev 3.6 (for M510), only one uploading to my controller.
I suspect (whitout any certitude) several revision with same Nb following your countries and your speed limit ? when i open the files .bin, the first 2 digit are not the same following rev who download and those don't
BAFANG have share with me several rev 3.6 (for M510), only one uploading to my controller.
I suspect (whitout any certitude) several revision with same Nb following your countries and your speed limit ? when i open the files .bin, the first 2 digit are not the same following rev who download and those don't
Dado
Active member
Mate, I dont have time to test every firmware - it is time consuming.
There is a mess in firmwares, lot of versions for different controllers, which are not compatible each other. M510 has now 4 controllers, M600 has two. As you said, it is diferentiated by first byte in bin file. If Besst wont start downloading firmware, your controller is not made for this firmware. Just dont understand why Besst can not give you any error message.
There is a mess in firmwares, lot of versions for different controllers, which are not compatible each other. M510 has now 4 controllers, M600 has two. As you said, it is diferentiated by first byte in bin file. If Besst wont start downloading firmware, your controller is not made for this firmware. Just dont understand why Besst can not give you any error message.
Last edited:
Dado
Active member
Dont think I have rights to upliad to github.
Dado
Active member
Interesting, where did u get this info? Could be they have disabled now power adjustments in new m600 controller just because of issues you writing.
I guess FC1.0 is now death and replaced by FC2.0.
Bafang M600 M510 M500 M820 M410 M200 AEG motor speed sensor kit-GreenBikeKit BBS, ebike batteries, Bafang M620, Bafang M600, Bafang M500, Bafang M510, KT controller with display-GreenBikeKit.com
Bafang M600 M510 M500 M820 M410 M200 AEG motor speed sensor kit for replacement.
www.greenbikekit.com
This one is based in US I think but shipping faster than AliExpress
Thx, i will contact themBafang M600 M510 M500 M820 M410 M200 AEG motor speed sensor kit-GreenBikeKit BBS, ebike batteries, Bafang M620, Bafang M600, Bafang M500, Bafang M510, KT controller with display-GreenBikeKit.com
Bafang M600 M510 M500 M820 M410 M200 AEG motor speed sensor kit for replacement.
This one is based in US I think but shipping faster than AliExpress
It's great news that with the new controller for the M600 you can program the performance using Beest pro.
I have an M500 motor, so if I swap the controller from the M600 in it, can I program the power in the M500?
Is my assumption correct?
Assuming, of course, that I reverse the power wires when changing the M600 controller to the M500 motor.
I have an M500 motor, so if I swap the controller from the M600 in it, can I program the power in the M500?
Is my assumption correct?
Assuming, of course, that I reverse the power wires when changing the M600 controller to the M500 motor.
temon10
Well-known member
remember only controller with 46.2 firmware can set parameter with besst pro. if u put m600 controller to m500 motor i think u have to change 1 cable connector.
Dado
Active member
EMTB Forums
Latest articles
-
Introducing the Forestal e-Cygnus - a downcountry and XC emtb
The new Forestal e-Cygnus is a slightly unusual emtb. It comes in two... -
2025 M1 Sporttechnik EN 8.0 review
The M1 EN is one of four M1 models built on the same frame. Well, it’s...