crazymelki
Active member
Thanks for the fast response. What you think, can I install this saddle also on my X-Fusion Manic on my Levo SL Expert?
Thanks for the fast response. What you think, can I install this saddle also on my X-Fusion Manic on my Levo SL Expert?
You will never be done with this kind of project
When you do take the bike out, you'll have to find a disgusting oily bit of tarmac to match up with and take the perfect photos ??
I can tell you 1000 million % that This is the wrong Post adaptor for 180 post mount forks .. the adaptor that’s in this post is for 160mm to 203mm post adaptor As this is the one I had to buy for my partners 160mm forks to 203 rotor .what ever you do do not buy this adaptor if your forks are standard 180mm . I know this as I fitted the correct adaptor . To my Lyrik forks that needed 23mm 180 to 203 . Pic below is the correct adaptor as you only need 23mm not 43mmSwapping the front and rear brakes from SRAM to Shimano XT was a massive upgrade. You would need to get the following:
- two new shimano olive and barb insert kits.
- Shimano brakes of your choice.
- Shimano mineral Oil and Bleed kit.
- New 6 bolt rotors of your choice (203mm front and 180mm rear ice tech is what I used).
- Caliper adapter for front 203mm shimano rotor. Make sure you get the one in the photo.
You need to cut the SRAM rear brake line at the lever and use a barb connector fitting (see photo) to attach an old brake line to the end you just cut and pull it thru to the rear swing arm. Then you attach your new shimano brake line to the barb on the old brake line and pull the new line back thru the swingarm and frame back to the bar. The barb has one left hand thread and on right hand thread.
Barb connector reverb stealth on amazon:
I can tell you 1000 million % that This is the wrong Post adaptor for 180 post mount forks .. the adaptor that’s in this post is for 160mm to 203mm post adaptor As this is the one I had to buy for my partners 160mm forks to 203 rotor .what ever you do do not buy this adaptor if your forks are standard 180mm . I know this as I fitted the correct adaptor . To my Lyrik forks that needed 23mm 180 to 203 . Pic below is the correct adaptor as you only need 23mm not 43mm
View attachment 29339
Ahhh so the post mounts on the Fox forks are 160mm then ? and not 180mm ..Killswitch...The F203P/P adapter below is the CORRECT one for mounting a Shimano 203mm rotor using Shimano brake calipers to the stock Fox fork on comp carbon SL. See photo below:
View attachment 29404
I tried the F203P/PM and it does NOT work. I bought and tried both adapters. As shown below the F203P/PM doesn't even come close to positioning the Shimano caliper in the proper place for the pads to contact the 203mm rotor.
View attachment 29422
Ahhh so the post mounts on the Fox forks are 160mm then ? and not 180mm ..
when you took the sram brake caliper off was there a 180mm adaptor on it to accomidate the 200mm sram rotor ?
Only works for SRAM rotor as they are 200mm and not 203mm. I tried it but the Shimano brake pads do not make contact with the entire Shimano rotor surface.Ahhh so the post mounts on the Fox forks are 160mm then ? and not 180mm ..
when you took the sram brake caliper off was there a 180mm adaptor on it to accomidate the 200mm sram rotor ?
Ay i know bud .. i got XTR on my stumpy using the lyrik RC2 and i bought the 20mm adaptor and the 203mm rotor was rubbing .. so had to buy the 203 adaptor which i put a link up for .. atleast i got it now so when i put my Lyrik ultimates on my carbon comp and new XTR 4pots ive not got to worry .. i do need to purchase the adaptor you have though as im still using the 2pot xtr on my stumpy as will the fox forks on that and use as my spare bike ..i will be switching wheels around on both bikes so it uses the same roteor .Only works for SRAM rotor as they are 200mm and not 203mm. I tried it but the Shimano brake pads do not make contact with the entire Shimano rotor surface.
@p3eps don’t think I’ve seen a weight yet for the carbon wheels. Will you get chance for that at some point?
maybe we can see whos wheels are lighter .. with mine being Nextie premium with added enduro strength ( added layers) .. built on DT swiss 240s . mine are 34mm wide .and straight pull spokes and direct mount discsI was just going with 1800g as per Specialized website.
I think it’ll be a while until I have the tyres off / sealant out / rotors off / cassette off etc to be able to give an accurate weight.
I could probably give you a wheel / rotor / cassette / tyre combined weight fairly soon as I have lovely iridescent bolts for the brake rotors on the way!
@p3eps Question: Do you use the AXS Reverb with 34.9mm diameter....or what is the reason the Levo SL S-Works comes with a 30.9mm? Is this frame related or do the use a post shim to reduce weight?
The World's largest electric mountain bike community.