Bafang Go+, is it a new App for all motors ?
- Thread starter Waynemarlow
- Start date
Now the question is where can we get a DP C245.C V3.0?
temon10
Well-known member
Ask my source but they now on Boat Festival holiday
I asked Linda to check with Bafang.
Answer
"
Dear Mike,
Yes, DPC245 is 2.0 version, it only fit go, can not fit go+, version 3.0 is better. We keep asking bafang to offer the 3.0 version, but bafang do not start mass production for 3.0 version, and in the marker, there just only some version 3.0 samples, we can get version around Aug, thank you very much.
Best Regards
Answer
"
Dear Mike,
Yes, DPC245 is 2.0 version, it only fit go, can not fit go+, version 3.0 is better. We keep asking bafang to offer the 3.0 version, but bafang do not start mass production for 3.0 version, and in the marker, there just only some version 3.0 samples, we can get version around Aug, thank you very much.
Best Regards
Last edited:
Yes I will post a picture next day when not working.
Not sure about the Wheel Size and Max Speed change. Will try to check.
Simebru635
Member
I have the same issue with the Go+ app, apparantly it only works with C245 controller which has the QR code PD051505 . Mine is PD051405 and will connect but with an error message. I havent tried the older app yet.
Did you ever solve this on-off issue. I have same problem with my m510.?Wrote to Bafang on 03/09/22
Also asked them for a firmware update for the M510 that could eliminate the 'on-off' torque issue.
No. Didn't get a response from Bafang... I have got an FC2.0 controller to try, which supposedly gets rid of the problem. Once fitted I'll post the outcome
Need cable.
Hardwire connections still
Did you ever come up with a solution to the on/off issue? I am experiencing same thing.Wrote to Bafang on 03/09/22
Also asked them for a firmware update for the M510 that could eliminate the 'on-off' torque issue.
Also, I upgraded my display to the DP C245.CAN so I could connect via Bluetooth using the Bafang Go app ( not the Go+). It connected fine but doesn’t really seem to do very much. I then installed the Go+ app on my iPhone and it finds my bike but won’t connect????
temon10
Well-known member
on off issue is common problem for FC 1.0 controller version, so the solution is change the controller to FC 2.0.
Only DP C245 3.0 bluetooth 5.1 can connect to Go+ App
Did you change your controller? If so, was the process reasonably smooth? Greenbike has the controller on their website - the “wording” says it’s the controller for “the FC 2.0 motor” - wording is a bit off , so wanting to make sure I am understanding you correctly ….
temon10
Well-known member
Bafang m510
The cheap way Is to obtain USB to can transreceiver And this extension cable. Check this forum. There is no need to buy overpriced best Tool or K1 flash if you dont want flash firmware... Edit: actually one can use ESP32 instead that transreceiver It will be even three times cheaper ...
www.emtbforums.com
U can read there, 2 people already confirm. I have FC 2.0 controller but not yet replace because I'm still on recovery for broken collarbone
I just sent this to Green Bike:Bafang m510
The cheap way Is to obtain USB to can transreceiver And this extension cable. Check this forum. There is no need to buy overpriced best Tool or K1 flash if you dont want flash firmware... Edit: actually one can use ESP32 instead that transreceiver It will be even three times cheaper ...
U can read there, 2 people already confirm. I have FC 2.0 controller but not yet replace because I'm still on recovery for broken collarbone
I have an m510 with a FC 1.0 Controller. I am experienced on/off power when pedaling. It was suggested to me that I need to upgrade the controller to the FC 2.0. Will this controller be compatible with the motor and the Torque Sensor?
Here is their answer:
No. FC1.0 controller only works with FC1.0 torque sensor.
FC2.0 torque sensor only works with FC2.0 controller.
Ms Anna Lee
www.greenbikekit.com
temon10
Well-known member
But @PadreParada confirm his old torque sensor compatible with 2.0 controller. if u wanna wait maybe next week I will try mine.
napshotman
Member
I confirmed that too as i have an old FC1.0, need to change torque sensor to match new controller FC2.0. I actually sent the FC1.0 motor back to factory to get it fixed. Best if you can go HK for holidays and at the same-time sent it back from HK (Hongkong) using SF freight forwarding. After that from factory to you, (ppl in the west) will be easier. That is a safer route IMO.
Simebru635
Member
Changzhou Fieldebikes Co., Ltd. - battery, ebike motor kits. Chloe has them for $70 US.
From the link above, though via Anna Shen : $95 with delivery and whatevers :
Can you check whether the basic parameters can be set above 25km/h and at the same time adjust the startup angle?
temon10
Well-known member
I think speed limit only can change via besst tool or usb dongle.
temon10
Well-known member
working for v3 version. Mine v3 version and working for go app+
EMTB Forums
Latest articles
-
A new standard for charging ebikes is coming? A quick interview with Bosch - charge2bike
I had a quick chat with dr Vikram Godbole about "charge2bike", a new...- Knut Nes
- 2 min read
- Views: 533
- Reaction score: 6
- Comments: 2
-
Introducing the Forestal e-Cygnus - a downcountry and XC emtb
The new Forestal e-Cygnus is a slightly unusual emtb. It comes in two...