My experience with them wasn't great. I was emailed to confirm receipt of the bike and that they have sent a report to their ”materials specialist” and will revert once they hear back. Two weeks later I received another email from one if the bike techs to say they are working on my bike and will keep me informed. I got the same email message three days running and then and email to ask for my shipping address now the repairs have been done. I had to phone canyon to ask what work was done.
Spectral ON 6.0 frame bearings failure, anyone else or just me !?
- Thread starter Jonah
- Start date
My experience with them wasn't great. I was emailed to confirm receipt of the bike and that they have sent a report to their ”materials specialist” and will revert once they hear back. Two weeks later I received another email from one if the bike techs to say they are working on my bike and will keep me informed. I got the same email message three days running and then and email to ask for my shipping address now the repairs have been done. I had to phone canyon to ask what work was done.
Nope. Everything is tight and right. I'm a weekend warrior, so the bike has a lot less usage than a typical 6 year old bike.
Hi.
Anybody know what kind of bearing I need to my Spectral.
I mean no. of bearing i.e. 6091, 61091 or so. I want to buy it outside canyon store because i don't want another chinese crap. Mine die after 400km.
Will by grateful for those numbers.
Cheers.
Anybody know what kind of bearing I need to my Spectral.
I mean no. of bearing i.e. 6091, 61091 or so. I want to buy it outside canyon store because i don't want another chinese crap. Mine die after 400km.
Will by grateful for those numbers.
Cheers.
G-Bru
Active member
The bearing numbers and sizes are listed in the parts diagram posted by Jonnymac in this thread:
Canyon Spectral:ON exploded parts diagram - EMTB Forums
See Jonnymac's last post for the updated diagram.
On a side note I noticed some play in my Spectral ON:7's shock extension and rocker arm. Upon further investigation, I found that the rocker arm bearings had completely seized. I ordered up some new Enduro Bearings to replace the cheap Chinese Cheezium bearings Canyon used. Friggin disgraceful really!
Apart from this, the bike is superb. I have upgraded a few components which has made the bike even more fun to ride!
- Luftkappe in the Lyrik with 160mm Shaft upgrade - this transformed the performance of the fork, loads of mid stroke support now!
- Super Deluxe in the rear with Meg Neg Air Can - no longer blowing through all my travel on big hits and loads more support whilst still maintaining small bump sensitivity/compliance.
- Rimpact Tyre Inserts
- E7000 Switch
- Wolftooth dropper lever
G
Last edited:
jpaulo.emtb
Member
I have contacted Canyon PT and Canyon ES, and they do not have the bushing replacement. They say that I have to find by myself. Canyon support, no comments.
The IGUS website do not have the IGUS Bushing ZFM-1012- 10. Only the ZFM-1012- 09 or IGUS ZFM-1012. Which one should i buy?
The IGUS website do not have the IGUS Bushing ZFM-1012- 10. Only the ZFM-1012- 09 or IGUS ZFM-1012. Which one should i buy?
Hakki
Member
I got WFM-1012-10 from Canyon couple of month ago. Those seems to be at least same level or maybe even better than original ones. I don't know what the originals was in my bike. ,
Of course ZFM-1012-12 can be shortened 2mm to 10mm lenght
Of course ZFM-1012-12 can be shortened 2mm to 10mm lenght
Cheekyweekesy
New Member
So my Neuron ON has gone the same way after 500 miles. Ordered some replacement and spare bushes on live chat. It’s now £3.95 PER bush plus delivery!!!
Does anyone know of a cheaper source? This is looking like a part that will need to be changed regularly
Does anyone know of a cheaper source? This is looking like a part that will need to be changed regularly
jpaulo.emtb
Member
Grilito
Member
After 250km I also had the same problem, I will contact the canyon to show my dissatisfaction with what happened, we are talking about 250km, 4 rails, is inadmissible.
Grilito
Member
Hi there. The guys that already changed these bushing already had problems with the second bushings or solved the problem once and for all? Regards
jpaulo.emtb
Member
I changed mines after 1200 kms. I bought from canyon 2 pairs. They cost me 20€. My bike is know with 2600 and so far so good.
davemcc1248
Member
Simplybearings do the SKF version PPMF 101212 for £3.28 a pair
and GFM-1012_10 for £5.26 a pair plus vat and £1.50 delivery. I have ordered both and will try the SKF ones first to see if they will last any longer .Also bought the max enduro bearings to try . Used them in my Orange before and last alot longer.
davemcc1248
Member
Have had my spectral on 6 for about 4 months. Getting bike ready for New years day spin noticed play in the bushings checked bearings and the ones top of horst link seized and bottom ones not much better. Contacted Canyon and got back replay (For all of the bearings to seize after 4 months of use is very unusual and suggests that either the conditions the bike is being used in are very harsh or the bike is not being washed/maintained correctly. ) and (We can supply replacement bearings of the same quality or alternatively most can be replaced with Enduro Max bearings which are a great option for longevity in harsh conditions ). Imagine using your mountain bike in harsh conditions LOL.
Lexinoo
Member
Are people still having problems with the bearings/bushes or were the replacements better?
I actually bought a spectralon back at the beginning of December, but on arrival it had a squeeky motor. With that and the tails of seized bearings and worn bushes I decided to get a refund and wait for something of a similar price to come up locally,but with the weather being as wet as it has I've just been using my clockwork bike or running instead.
But now I see Canyon have got a sale on and I could pick up a neuron 5 for £2600 or neuron 6 / spectral 6 for £2900 it's sent my mind spinning again ?!
I actually bought a spectralon back at the beginning of December, but on arrival it had a squeeky motor. With that and the tails of seized bearings and worn bushes I decided to get a refund and wait for something of a similar price to come up locally,but with the weather being as wet as it has I've just been using my clockwork bike or running instead.
But now I see Canyon have got a sale on and I could pick up a neuron 5 for £2600 or neuron 6 / spectral 6 for £2900 it's sent my mind spinning again ?!
Grilito
Member
Just Change the second par of bushings on spectralon with 1800km, this time i go try skf bushings, but i doubt it solve the problem.
Lexinoo
Member
Hmmm,not very good really is it.
jpaulo.emtb
Member
Anyone knows what are the headset bearing of the Canyon Spectral? Mines are gone!!!
G-Bru
Active member
Lower is 40mmx52mmx7mm with 45 degree chamfers for the crown race.
Cheekyweekesy
New Member
Do you know what the top headset bearing is?
jpaulo.emtb
Member
jpaulo.emtb
Member
Nop. The look like this. And they haven't dimensions.
Hi. Thank you to everyone re your comments on the frame bearings. I'd like to order a complete set, so I have things to hand should it become an issue, so I have annotated the exploded diagram attached. If those in the know, or just generally curious, could take a look and let me know if I have any of the bearing refs incorrect, I'd appreciate it. From looking at Simply Bearings website, you can get a pack of 10 bushes (part 23) for around £6.50, and if its only a 10 minute job then, whilst slightly annoying, its like brake pads..... I've also added some bearing 'tips' websites to the pdf, re what '6801RS' actually means.
As a complete aside, reason I am doing this is a long time ago I noticed that my Transition Smuggler was letting go at the rear end on sections of trail where it hadn't done before and on checking the bearings a couple were seized. Amazing difference fitting new ones made, so something worth checking now and again (and why I plan to have the spares in).
Not that I am getting out on it at the moment, with Covid-19 restrictions - its all gentle local XC and road rides on my analogue bikes. Getting me fit though. Cheers.
As a complete aside, reason I am doing this is a long time ago I noticed that my Transition Smuggler was letting go at the rear end on sections of trail where it hadn't done before and on checking the bearings a couple were seized. Amazing difference fitting new ones made, so something worth checking now and again (and why I plan to have the spares in).
Not that I am getting out on it at the moment, with Covid-19 restrictions - its all gentle local XC and road rides on my analogue bikes. Getting me fit though. Cheers.
Quick update. Found this, which is a great resource for understanding bearing naming convention: Bearing Technical Information - Hambini Engineering
Cheekyweekesy
New Member
Does anyone know the torque settings for the motor bolts?
G-Bru
Active member
G-Bru
Active member
Those are the Acros upper and lower complete headset cups and bearings. Press the old bearings out and refit with new bearings (I did mine yesterday). Its that or buying the entire upper and lower cup with bearings!
G
I noticed some play when lifting the rear of the bike, so decided to check the bushings. Took 20 mins going slow and steady to replace them and play is now gone. Just in case anyone is interested, this is what I did:
Tools:
20Nm torque wrench with 5mm and 6mm allens (or was it 4mm?)
Shock pump
Bolt thread grease (I always grease threads)
Some threaded bar with nuts and washers, or a bearing press (or stronger fingers and thumbs than I've got to push the bushings in - lightweight!)
A bike workstand
GT85 and a rag
Job:
Drop the rear wheel out
Let all the air out the rear shock (note psi)
Remove the 6mm bolt
Remove the 5mm bolt (or was it 4mm?)
Pull the busing out with your finger nail or a flat blade driver
Spray GT85 into holes and clean with a rag - including checking/cleaning the bearings, mine were okay so not replacing yet
Press in new bushes
Clean bolt threads, grease and re-fit, torque to 20 Nm
Refit rear wheel
Pump up shock
Lift rear of bike and see if play is gone. If the answer is no, you might need to replace bearings, but it'll probably be fine given the number of people who have had these bushes fail. And see my earlier post re buying a pack of 10 of these for £6.50.
Tools:
20Nm torque wrench with 5mm and 6mm allens (or was it 4mm?)
Shock pump
Bolt thread grease (I always grease threads)
Some threaded bar with nuts and washers, or a bearing press (or stronger fingers and thumbs than I've got to push the bushings in - lightweight!)
A bike workstand
GT85 and a rag
Job:
Drop the rear wheel out
Let all the air out the rear shock (note psi)
Remove the 6mm bolt
Remove the 5mm bolt (or was it 4mm?)
Pull the busing out with your finger nail or a flat blade driver
Spray GT85 into holes and clean with a rag - including checking/cleaning the bearings, mine were okay so not replacing yet
Press in new bushes
Clean bolt threads, grease and re-fit, torque to 20 Nm
Refit rear wheel
Pump up shock
Lift rear of bike and see if play is gone. If the answer is no, you might need to replace bearings, but it'll probably be fine given the number of people who have had these bushes fail. And see my earlier post re buying a pack of 10 of these for £6.50.
FSEngineer
New Member
Hi guys, for anyone else having this problem in future you can actually get harder-wearing bronze bushings which fit in the shock carrier and seem to make everything a bit tighter. After going through a set of nylon bushings every winter I'm hoping these will last a bit longer. Check out my post in the below thread for info:
www.emtbforums.com
Canyon spectral on play in shock carrier
After taking bike to shimano service centre motor problem they said I had play in rear bearings after changing them there’s still play it’s where the rear shock carrier attaches to pivot it’s just a barrel on a thread no bearing anyone else noticed this I think it’s not an issue just part of...
www.emtbforums.com
Similar threads
EMTB Forums
Latest articles
-
Introducing the Forestal e-Cygnus - a downcountry and XC emtb
The new Forestal e-Cygnus is a slightly unusual emtb. It comes in two... -
2025 M1 Sporttechnik EN 8.0 review
The M1 EN is one of four M1 models built on the same frame. Well, it’s...