Lack of EP6 tuning parts

[Bigun]

Hi there, thanks for the add.
I have a 2024 Merida e160 700se with the EP6 motor with the latest software 4.3.
I am looking for either a chip to derestrict or something like Planet 3 or Speedi unit for the rear hub.
Everywhere I look, the chips are out of stock (almost as if pulled off the shelf under pressure from Shimano?) and the Planet 3 will not fit my centre lock rear hub. (I'm told from Planet 3)
I have been told by many companies that the EP6 and EP801 cant be chipped or tuned!
The bike is only a few months old and it looks like I may be stuck with a lemon.
Any advice would be greatly appreciated

Kevvo

 

[HandsomeDanNZ]

The EP6 (and EP801) can definutely be derestricted, as is evident from the number of bikes available in markets where there aren't legal resrictions on assistance speed.
For example, here in NZ, there's a few bikes that have standard speed restrictions at or about 45km/h - Merida e160's included (mine, which runs the EP6, was set to max assistance of 45km/h by a Shimano rep before i bought it).
I've also seen an EP801-equipped Polygon with advertised assistance up to 45km/h, so it's definitely not a hardware or software issue, but an availability/legal issue, I think.

 

[Astro66]

I have been told by many companies that the EP6 and EP801 cant be chipped or tuned!

Do not chip or try anything with the speed sensor. You will lock the motor and need Shimano to unlock it, with your motor marked permanently as being tampered with, thus no warranty.

I have the same bike and motor. I have derestricted it using the EMax Software. Contact Peter or Max at EMax tuning. They will get it done for you, for 119 Euros.

My bike has done 400km since the EMax upgrade. It works perfectly, up to 50kph. Including the speed reading perfectly.

Just a note. They are currently working on the software release for the new 4.3 firmware. I have the 4.2 upgrade and I am waiting for them to let me know when they have the 4.3 version ready. So currently I have left my bike with the 4.2 firmware. You may want to wait till they have the 4.3 firmware ready, which Peter has said will be a few weeks.

Home EN – eMax Tuning

www.emax-tuning.com

 

[Bigun]

The EP6 (and EP801) can definutely be derestricted, as is evident from the number of bikes available in markets where there aren't legal resrictions on assistance speed.
For example, here in NZ, there's a few bikes that have standard speed restrictions at or about 45km/h - Merida e160's included (mine, which runs the EP6, was set to max assistance of 45km/h by a Shimano rep before i bought it).
I've also seen an EP801-equipped Polygon with advertised assistance up to 45km/h, so it's definitely not a hardware or software issue, but an availability/legal issue, I think.

Thank you HandsomDanNZ for the reply. Here in the UK we have a stupidly low max speed of 16mph/25kmh. As you state, it's just a software issue as the same motor is used world wide with different legal top speeds. It's just that overnight, every tuning kit was "sold out" on every site and still aren't available at time of post some months later? A bit suspect if you ask me

 

[Bigun]

Do not chip or try anything with the speed sensor. You will lock the motor and need Shimano to unlock it, with your motor marked permanently as being tampered with, thus no warranty.

I have the same bike and motor. I have derestricted it using the EMax Software. Contact Peter or Max at EMax tuning. They will get it done for you, for 119 Euros.

My bike has done 400km since the EMax upgrade. It works perfectly.

Just a note. They are currently working on the software release for the new 4.3 firmware. I have the 4.2 upgrade and I am waiting for them to let me know when they have the 4.3 version ready. So currently I have left my bike with the 4.2 firmware. You may want to wait till they have the 4.3 firmware ready, which Peter has said will be a few weeks.

Home EN – eMax Tuning

www.emax-tuning.com

Astro66, thanks for the info. I updated mine to 4.3 as soon as it was released unfortunately (should have waited) Both times ir has updated it has left error code 203 in the app. Is this usual?. Is it possible to go back to a earlier software setting of needed?

 

[Astro66]

Astro66, thanks for the info. I updated mine to 4.3 as soon as it was released unfortunately (should have waited) Both times ir has updated it has left error code 203 in the app. Is this usual?. Is it possible to go back to a earlier software setting of needed?

Yes. That is a software bug. E203 is an error saying that you have electronic devices pluged in that are not configured. As long as you are not getting that error on the bike screen. It should be fine. But perhaps check with where you bought the bike.

You cannot rollback firmware versions. I was told that by Peter at EMax, who is an expert on the Shimano software.

Contact Max or Peter by email. They can do the 4.3 derestriction, doing a remote session of your computer. But they are super busy, and it might be easier to wait till they have finished the 4.3 update. You will need a PCE02 cable, which is expensive. I borrowed one from my LBS, but many shops won't do this.

EP801 E203 code

Hey everyone, Been riding my Bullit for a couple months now and absolutely love it. My only issue has been an error code that popped up each of the 2 times I used the E-Tube app to install a motor update. The error code reads E203 and says the motor isn't going to function, but the bike...

www.emtbforums.com

 

[Bigun]

Thank you so much. At least there may be some light at the end if the tunnel. I will try them in a few weeks to see if they're ready with the new version.

 

[Paulquattro]

Welcome to the site .

 

[Bigun]

Thank you. All good, positive advise so far

 

[Mr-EPIC-3]

FYI

PearTune MSO Tuning e-bike Shimano EP6/EP801 |Pear Control

 

[Bigun]

FYI

PearTune MSO Tuning e-bike Shimano EP6/EP801 |Pear Control

Thank you

 

[Mr-EPIC-3]

Thank you

I been using the PearTune MSO EP6 for a year now, running firmware 4.2.3., no issues.

 

[Bigun]

I been using the PearTune MSO EP6 for a year now, running firmware 4.2.3.

Unfortunately I'm on 4.3 so waiting for an update for the latest one

 

[Mr-EPIC-3]

Unfortunately I'm on 4.3 so waiting for an update for the latest one

You could ask them if they have tested with 4.3.

 

[Bigun]

View attachment 146530
You could ask them if they have tested with 4.3.

I have done. They're about 3/4 weeks into testing for the new software ?

 

[johnnybb2000]

I been using the PearTune MSO EP6 for a year now, running firmware 4.2.3., no issues.

Hi Mr-Epic-3!
I bought the same "upgrade" for my EP6 RS on a ORBEA Rise H30 2024. I took it to 3 of my local bike shops and none would install it. I would try to install myself but, there are no videos/resources online showing any info how to fit. Can you give any pearls of wisdom for install? Does anyone else have any step by step instructions for install please??

 

[Mr-EPIC-3]

Hi Mr-Epic-3!
I bought the same "upgrade" for my EP6 RS on a ORBEA Rise H30 2024. I took it to 3 of my local bike shops and none would install it. I would try to install myself but, there are no videos/resources online showing any info how to fit. Can you give any pearls of wisdom for install? Does anyone else have any step by step instructions for install please??

You should have gone a install guide with the PearTune device. But let me find my install guide and I will send over a photo of it.

 

[johnnybb2000]

You should have gone a install guide with the PearTune device. But let me find my install guide and I will send over a photo of it.

Hi Mr-E, thanks so much for reply. I got one but it seemed to be for the EP800. Didn't get one that showed how to get into the EP6 RS. Reckon I got to take the motor off... But, there's no online videos to show how to do that. Any help appreciated sir!

 

[Mr-EPIC-3]

Hi Mr-E, thanks so much for reply. I got one but it seemed to be for the EP800. Didn't get one that showed how to get into the EP6 RS. Reckon I got to take the motor off... But, there's no online videos to show how to do that. Any help appreciated sir!

It's the same wire diagram, rear wheel sensor plugs into the PearTune and the PearTune plugs into the port that the rear wheel sensor was plugged into

 

[johnnybb2000]

It's the same wire diagram, rear wheel sensor plugs into the PearTune and the PearTune plugs into the port that the rear wheel sensor was plugged into

Hi Mr-E,
Appreciate your time to respond however, please don't assume my bike mechanical expertise! I am looking for basics, perhaps videos for step by step?
I believe I have to remove my (EP6 RS) motor to install (no videos found). Then I have to connect within the EP6 RS motor. Maybe I sound too stupid but, just want to be able to install without breaking things.
Again, your time and guidance is genuinely appreciated.... The chip doesn't even represent a decent €250 book shelf!!

 

[johnnybb2000]

Hi Mr-E,
Appreciate your time to respond however, please don't assume my bike mechanical expertise! I am looking for basics, perhaps videos for step by step?
I believe I have to remove my (EP6 RS) motor to install (no videos found). Then I have to connect within the EP6 RS motor. Maybe I sound too stupid but, just want to be able to install without breaking things.
Again, your time and guidance is genuinely appreciated.... The chip doesn't even represent a decent €250 book shelf!!

To elaborate, I have my Orbea Rise H30 2023, with a EP6 RS motor. I have bought the PearTune "upgrade" and the instructions don't really say tóo much. So, I am sat, looking at my bike/motor, without any specific tools thinking.... "Ok, how am I gonna fit this then?"
🫣🫣