Ebike stands?

Rob Rides EMTB

Administrator
Staff member
Subscriber
Jan 14, 2018
6,260
13,700
Surrey, UK
Well folks,

I took the plunge and purchased this and got it delivered from Italy. I do have a proper ‘bike service stand’ very similar to the Feedback stand but for me, as this stand lifts both wheels off the ground and they way I am used to washing and servicing my analogue bikes this is a much better option for me.

The plate underneath the motor is padded and also adjustable up and down. The point that connects to the downtube is also padded so it is a well thought out design.

Mounting the bike was tricky the first time as you need to line everything up but now it is ‘adjusted’ to suit my bike which took a few minutes it can be mounted and unmounted in seconds.

View attachment 611
View attachment 612
Really interesting product. Can you put a review in the review section?
 

Kiwi in Wales

Short cranks rule!🏴󠁧󠁢󠁷󠁬󠁳󠁿
Patreon
Founding Member
Jan 24, 2018
1,241
1,589
Carmarthen, Wales
Not
This part just presses on the crank bolt?
View attachment 613 [/
This part just presses on the crank bolt?
View attachment 613
Yes, that is correct.

Not sure what ebike you have?

On my Levo there is a 6mm hole that goes right the way through the middle of the crank bolt. The crank is also hollow so the bit you are showing inserts all the way through the crank bolt hole and into the hole in the crank and butts up against the stopper (the disk bit showing in the picture)
 

Kiwi in Wales

Short cranks rule!🏴󠁧󠁢󠁷󠁬󠁳󠁿
Patreon
Founding Member
Jan 24, 2018
1,241
1,589
Carmarthen, Wales
Really interesting product. Can you put a review in the review section?
I will try to get some time this coming week to do a review. I am currently writing a long winded thread on the Levo/Kenevo post as I have carried out a few upgrades since my purchase off ccrdave which may get a few interesting comments back.....
 

eFat

Active member
Founding Member
Feb 4, 2018
342
270
Switzerland
On my Levo there is a 6mm hole that goes right the way through the middle of the crank bolt. The crank is also hollow so the bit you are showing inserts all the way through the crank bolt hole and into the hole in the crank and butts up against the stopper (the disk bit showing in the picture)
I don't have a Levo but it's a Brose motor too. Are you saying that the crank bolts are completely hollow? Mine are not and I was thinking about drilling them...
 

Kiwi in Wales

Short cranks rule!🏴󠁧󠁢󠁷󠁬󠁳󠁿
Patreon
Founding Member
Jan 24, 2018
1,241
1,589
Carmarthen, Wales
I don't have a Levo but it's a Brose motor too. Are you saying that the crank bolts are completely hollow? Mine are not and I was thinking about drilling them...
That is not going to be an easy task to do especially if the bolt is hardened, been there tried that and it took absolute ages and killed 3 drill bits ?

You will be please to know that you can buy a bolt with a 6mm hole pre drilled through it off Ebay or any Internet seller. You only need one for the left hand side. What cranks are on you bike?
 

eFat

Active member
Founding Member
Feb 4, 2018
342
270
Switzerland
I have Miranda Delta cranks. I searched (poorly apparently) for bolts with a hole but couldn't find any. Will try harder :) Thanks
 

Kiwi in Wales

Short cranks rule!🏴󠁧󠁢󠁷󠁬󠁳󠁿
Patreon
Founding Member
Jan 24, 2018
1,241
1,589
Carmarthen, Wales
I have Miranda Delta cranks. I searched (poorly apparently) for bolts with a hole but couldn't find any. Will try harder :) Thanks

Hi, I had a look at the Miranda delta cranks. Can you check if the bolt that attaches to the ISIS fitting has a 15mm diameter? Also if the head of the bolts diameter is 22mm then what is pictured below is what you will need. It has a 7mm hole and is also self extracting as well ?

D8C3D83E-FEE1-47BA-9189-E08139C1EEE7.jpeg
 

Eckythump

Well-known member
Founding Member
Jan 16, 2018
832
680
North Yorkshire
I was thinking of making a stand to support the underside of the chain stays on my bike then low & behold what pops up on embn.......
(Nice tip on using walk mode for chain cleaning! 13:30ish)

FFCA112C-2D2D-4110-939D-9A5BF06B582A.png
 

grantini

E*POWAH Master
May 7, 2019
611
539
Delaware
I used a good old fashioned Park shop stand.... it's pretty flexible and practical, folds pretty flat, and allows you to move the bike around. I've had it so long that I used to use it on the top bar of the frame.... I guess I don't have a picture of it with my ebike in it....

11893854_10207239729729097_1610319754486158494_o.jpg
 

grantini

E*POWAH Master
May 7, 2019
611
539
Delaware
I was thinking of making a stand to support the underside of the chain stays on my bike then low & behold what pops up on embn.......
(Nice tip on using walk mode for chain cleaning! 13:30ish)

View attachment 691
walk mode is awesome for lot's of cools stuff, not just cleaning but when you throw your chain, pull it in a couple rings, shift up, and then lift and press walk mode... bam... back in business
 

TR5_20

Active member
Nov 22, 2020
81
65
Scotland

Kernow

E*POWAH Elite World Champion
Patreon
Founding Member
Jan 18, 2018
1,436
1,149
Cornwall uk
That Gioma stilo stand looks ok for cleaning etc , £28 on eBay but better than the strap method I think
 


EMTB Forums

Since 2018

The World's largest electric mountain bike community.

555K
Messages
28,048
Members
Join Our Community

Latest articles


Top