Search results

Well it has certainly been a sweet time working on this Yammy motor. No surprises except for the clip that was out of position. It looks quite well built and I like it overall…. until I actually try to kick it over 🧐 IT better work 😬 Here it is almost , just need to apply the sealant and...

I love when everything is perfectly clean and sparkling! Here’s the sprag clutch and crank, everything looks good, with next to no wear at all. 👍 I’m getting there slowly 🐢

Thanks for the tip bm I appreciate it… I have a sneaky feeling everything is going to fire up perfectly 🤞

How exactly does the torque sensor work ? I see there’s a gear with strange cuttings on the shaft that slips inside the torque sensor. What’s the dealio , how does this actually work ? 🤔😎thanks 🍻

You bet you can ! Stans makes them. https://www.bikeinn.com/bike/stans-no-tubes-tubeless-schrader-valve-pair/137654247/p

Hahaha 😝 if you think that’s bad just wait til the horses and dirt bikes come through. I just hit the trail and didn’t have a chance to pick anything not even the flowers 💐

OMG !😱Now I see where my spare motor is !!! Yamaha just updated my back order back order… 210 days left to count … seriously !? 😩

I believe I have found the home for that washer ! It must have possibly fallen off in my disassembly. 😬

Well I have cleaned everything up , replaced the main crankshaft bearings. Started attempting a dry fit for everything before I lube and seal but I am not positive exactly what kind of washer this is and exactly where it goes. I found it between the torque sensor and outer case but that location...

I don’t know man , it takes a Lot of guts, skill and strength dropping monolithic trees with a 36” fire breathing Sthil. Your da man Sthildog 👍

On the very first ride on my brand spanking new Yamaha Moro Pro, I totally forgot it wasn’t a motorcycle and got totally carried away. Bike started to jerk and stop n start. Looking down I saw the chain acted like a mud scoop dumping mud n small rocks throughout the entire drive system. It was...

I have been scouring the net about this issue and it seems to vary hugely, from the same day to over 6 months +. A number of riders who had to wait months asked for a complete refund.

Hey it seems that it doesn’t matter what brand of ebike, warranty or not , it’s going to be a while. I have been looking for a spare Yamaha pw-x2 motor for at least 6 month now. 😧 Woops I see the OP is over a year ago now , update would be nice , how long did it take to finally get yours ? 😬

Hey Mikerb the display does have a 3volt button cell. I did remove it and checked it with my meter and all seemed well. Reinserted , no difference. The main battery was showing 30% , when I arrived home and removed the battery and looked at the “fuel” gauge on it , it showed close to the same...

Vent hole you say 🧐… Lookie here …

Mikerb I believe the switch may indeed be a red herring. I have since split the cases and have found water droplets everywhere. It looks like something that was put in a freezer and then thawed out. Is it possible that condensation can build up just from a huge temp swing ? I have been riding...

Great info here, thanks guys 👍

For those of you who have had a motor or two or three replaced under warranty in the past year or so , how long did you have to wait ? Doesn’t matter what Brand. Thanks 😎

Hmmmm perhaps the reason the seal failed is because the bearings did first. The excessive play in the bearings would quickly take out the seal. If that’s the case then, if we checked the play in the crank after Every ride , we could change out the bearings before the seal goes and lets in the...

I actually saw this site and I cannot find any Yamaha part number or which bike application it fits. Plus the buttons are different then mine. The problem being if I just take a chance and it doesn’t fit, there is No returning. The listing says they have it in stock but we all know that’s not...