Chain not settings on cassette
- Thread starter silles
- Start date
Amber Valley Guy
Active member
It's a shifting ramp, makes gear changes easier, by disengaging the chain from the sprocket teeth.
juggernaut
Member
Chain is stretched or wrong chain.
Doesn’t even look like the KMC chain is their e-bike rated chain. Which I don’t rate that great anyway - stretched mine in less than 800 klms. Compared the sram gx chain on my other 1800w eMTB which is still perfect after 1200klms.
Doesn’t even look like the KMC chain is their e-bike rated chain. Which I don’t rate that great anyway - stretched mine in less than 800 klms. Compared the sram gx chain on my other 1800w eMTB which is still perfect after 1200klms.
Last edited:
Cassette is toast, same with the chain. Alloy cogs are dumb on e bikes. Think I am wrong, pick up a cheap chain gauge and check it.
I am a big guy(100 kg) and I spend most of my time in eco on my Kenevo, my chain is toast in 500 miles. If you are running full power a lot, you can kill a chain quick. My advice is buy good chains and crap cassettes. Higher end cassettes have 1-4 alloy cogs, alloy cogs suck for e bikes. Good chains have higher end parts and tend to last longer.
I am a big guy(100 kg) and I spend most of my time in eco on my Kenevo, my chain is toast in 500 miles. If you are running full power a lot, you can kill a chain quick. My advice is buy good chains and crap cassettes. Higher end cassettes have 1-4 alloy cogs, alloy cogs suck for e bikes. Good chains have higher end parts and tend to last longer.
The 11th speed cog is completely shark toothed. Where are you getting the 400km number from? An app, a guess. If it’s a guess, I always underestimate my mileage on an e bike. My app claims my bike has over 1800 miles on it, I would never guess that number.
steve_sordy
Wedding Crasher
The cassette looks fine to me. I see no signs of shark-toothing and minimal burring. I agree with @RustyMTB about the B-screw, that upper jockey wheel looks too far away from the cassette.
Setting up 12-speed from scratch always seems to take me longer than ever it did with 9-10 speed. So it is worth consulting a guide from somewhere like Park Tools to ensure that you have not missed a step, or carried it out incorrectly.
I agree with @mustclime that "good chains have higher end parts and tend to last longer". As chains wear, they start to slide up and down the tooth face (creating the shark-toothing); not just on the cassette but on the front ring. Money spent on a good chain is seldom wasted. Not only do they make the rest of your transmission last longer, they tend not to rust quite so quickly.
I also agree with @juggernaut and @mustclime that you should keep an eye on what is known as chain stretch. It's not really "stretch" as such but as the chain gets longer it's not a bad description. So buy a chain gauge, or better still remove the chain and measure it with a metal tape measure. Stretch the chain over a flat surface and measure 100 links from pin to pin. A new chain will measure exactly 50". A terminal one will measure 50-3/8" (ie 0.75% worn). Because the wear accelerates towards the end, I and many others tend to replace at anything above 0.6%. (50.3"). Measuring to 0.3 on a typical imperial tape measure is tricky, so go for 50-5/16" (0.0625%), which is not only close enough, it's also easy to do.
Do not rivet your chain back together, instead take the opportunity to fit a quick link. Google it!
Setting up 12-speed from scratch always seems to take me longer than ever it did with 9-10 speed. So it is worth consulting a guide from somewhere like Park Tools to ensure that you have not missed a step, or carried it out incorrectly.
I agree with @mustclime that "good chains have higher end parts and tend to last longer". As chains wear, they start to slide up and down the tooth face (creating the shark-toothing); not just on the cassette but on the front ring. Money spent on a good chain is seldom wasted. Not only do they make the rest of your transmission last longer, they tend not to rust quite so quickly.
I also agree with @juggernaut and @mustclime that you should keep an eye on what is known as chain stretch. It's not really "stretch" as such but as the chain gets longer it's not a bad description. So buy a chain gauge, or better still remove the chain and measure it with a metal tape measure. Stretch the chain over a flat surface and measure 100 links from pin to pin. A new chain will measure exactly 50". A terminal one will measure 50-3/8" (ie 0.75% worn). Because the wear accelerates towards the end, I and many others tend to replace at anything above 0.6%. (50.3"). Measuring to 0.3 on a typical imperial tape measure is tricky, so go for 50-5/16" (0.0625%), which is not only close enough, it's also easy to do.
Do not rivet your chain back together, instead take the opportunity to fit a quick link. Google it!
Focus on your symptom: poor shifting. Like the others have suggested, check your B screw. I like to run my jockey wheel closer than you read about in the books. If you set the jockey wheel further away, then expect shifting problems. Check your high and low limits. I run mine a little further out than the YouTubers might recommend. Only after everything else is perfect, then worry about adjusting your cable tension.
Since the bike only has 400 km on it, we can almost certainly eliminate wear as being a problem. Only in the most absurd cases can you visually identify a worn chain or cassette. Get yourself a chain checker. Even if you don't need it today, you'll need it some time soon.
Lastly, since I can't see the rest of your drivetrain, I can't diagnose anything from your picture. But keep in mind that a roller chain does NOT ride in the valley between the teeth on the sprocket. The roller chain rides on the leading edge of each tooth. If the chain is riding in the valley, then things are worn out and it will not run nicely.
One last thought: Check the flexibility of each individual link. If it's binding in any way, it will cause shifting problems.
Since the bike only has 400 km on it, we can almost certainly eliminate wear as being a problem. Only in the most absurd cases can you visually identify a worn chain or cassette. Get yourself a chain checker. Even if you don't need it today, you'll need it some time soon.
Lastly, since I can't see the rest of your drivetrain, I can't diagnose anything from your picture. But keep in mind that a roller chain does NOT ride in the valley between the teeth on the sprocket. The roller chain rides on the leading edge of each tooth. If the chain is riding in the valley, then things are worn out and it will not run nicely.
One last thought: Check the flexibility of each individual link. If it's binding in any way, it will cause shifting problems.
- Thread starter
- #9
Thanks for all the replies
Bit more info. Bike is Giant Trance X E+3
I checked millage in app. But I rode the bike about 10 times. Mostly low assistant mode, I am light.
I used the schimano guide to setup.
Lined up 51t mark on cage, etc.
But it wasnt shifting perfectly, had to make it even closer. As per this article
Chain has light wear <0.5%
Maybe it is the disengaging ramp
Whatever that would be
Ill keep digging.
Cheers
Bit more info. Bike is Giant Trance X E+3
I checked millage in app. But I rode the bike about 10 times. Mostly low assistant mode, I am light.
I used the schimano guide to setup.
Lined up 51t mark on cage, etc.
But it wasnt shifting perfectly, had to make it even closer. As per this article
Chain has light wear <0.5%
Maybe it is the disengaging ramp
Whatever that would be
Ill keep digging.
Cheers
Put the bike in a stand & rotate the crank very slowly whilst watching the chain between the guide pulley & the cassette. You'll be able to see exactly how it's engaging with the teeth & where it's meshing with the cassette. From there, you'll be able to see work out the adjustments needed.
KMC chains aren't directional so it can't be mounted the wrong way round. It looks like it's engaging ok but the chain gap longer than the tooth width. One easy thing you could try is to advance the chain on the cassette one link from where it sits now, see if it sits correctly after that.
Astro66
Active member
B screw set too high. Too much gap between cassette and derailleur cog. But you'll always get a little bit of unsettled chain where the chain first contacts the cassette in first gear.
Adjust b screw but don't panic. It's not a problem. I have the same cassette and chain.
Not sure how much u can see
Yeah, not sure what you're showing us. When you're riding the bike, what's the problem?
Similar threads
EMTB Forums
Latest articles
-
Introducing the Forestal e-Cygnus - a downcountry and XC emtb
The new Forestal e-Cygnus is a slightly unusual emtb. It comes in two... -
2025 M1 Sporttechnik EN 8.0 review
The M1 EN is one of four M1 models built on the same frame. Well, it’s...