The odometer miles are tied to the motor. If the motor is replaced the miles start at 0 again. You need to update the firmware in the TCD display.
I have several rides in now since my two TCD's were updated and it appears that the issue is finally gone, If it does happen again I will be sure to...
Yes, it was for you, I am somewhat new to forums and should have used reply. Thank you for taking the time to fully explain and share your knowledge.
I am pretty sure you are correct and it was actually my sprag clutch failing. I would hear the motor spin up every once in a while for just a...
Where did you learn that it should be changed at 10,000? miles? Based on what you have seen do you agree with that or would you recommend changing it sooner? I know that any belt has an expected service life and I want to be prepared to replace it at some point instead of waiting until it fails...
Mine did the same exact thing after motor replacement but my problem was deeper. Removed the motor and found the two nuts for these rear bolts were installed improperly. I initially tightened them like you did but creek was back after a few rides. Picture shows scars left behind after I removed...
My second motor has the new belt and now has 1100 miles. My wife's motor has the old belt and now has 1500. Both motors now have the latest firmware and no problems at this time.
The highest I saw anyone report in another post was 3600 miles.
This motor is still under warranty, it was replaced under warranty about 6 months ago and now has about 1400 miles. First one only lasted 1100 miles.
I still think this is more that water. The only water this motor has ever seen is when I wash the bike, and then I only sprinkle it from above to...
thanks, how did you know all this? Looks like you have the rev notes but only shared pieces. I always take time to read through rev notes before updating anything and they are typically available. Are these notes available and if YES where can I find them.
I never had a motor error until after...
Thank you @Bearing Man for responding. I agree, the price is outrageous. I also originally though it was water in the gasket too, until I saw the instruction manual and the use of Vaseline on the belt. There is also a video on Youtube showing the procedure and they also used vaseline on the...
Do they ever publish release notes? I have asked rider care several times and they dont know about it. I have asked them several times what is the most current firmware and they dont even know that! The just say take it to a dealer to be updated. I have made more that one trip to a dealer for...
Specialized is as bad or worse as everyone else. Check out my post about creaking sound when pedaling. Took five weeks to get the motor swapped out and months to find the mistakes they made. I found my new motor has a problem and they wont even acknowledge it. Offered to send puctures and they...
Does anyone in the USA have experience with the Brose kit that upgrades the motors to the new belt?
I attached a copy of the installation manual from the kit so I know it exists.
You can get it online from overseas but shipping is slow and expensive.
Specialized assured me it was the seat post or water. I offered to send them the picture but they declined. I did let them know the pictures were on this forum so hopefully they see it and respond.
Here is a picture looking up the frame at the bottom of the seat post, pretty sure its not leaking...
Has anyone ever seen this before? You can only see it if you take the motor out of the bike.
There was a slight gap near the gasket. The two screws in the picture were loose and I was able to tighten them and see the gap close. Specialized claimed there was nothing inside to leak but after...
mine was much more difficult to find, motor was replaced by dealer and they installed it wrong. i made a post yesterday, long story but worth the read.
One other thing I forgot to add about the motor. Specialized did say its probably not leakage because there is nothing to leak. I agreed with that statement. I do think that water may have contributed to this. Somehow the screws became loose, I know that to be a fact. Once loose water would tend...
I see the names of the pictures do not show up in the post. There are two pictures of the buidup on the motor cover gasket, one before I found the loose screws and one after I removed them. The screws are sitting on the table in one of the pics and you can see there was never any thread locker...